- suitable torch: Prestocut 600
- small cutting gap - low material loss
- excellent cut quality
- higher cutting speed
- optimized gas consumption
| type | FCN 0150N-PM-06 | FCN 0300N-PM-06 | FCN 0500N-PM-06 | FCN 0700N-PM-06 |
| cutting thickness range | bis 150 mm | bis 300 mm | bis 500 mm | bis 700 mm |
| cutting oxygen consumption | 33 Nm³/h | 65 Nm³/h | 77 Nm³/h | 140 Nm³/h |
| cutting oxygen pressure | 10,5 bar | 10 bar | 8 bar | 10 bar |
| heating oxygen consumption | 6 Nm³/h | 6 Nm³/h | 17 Nm³/h | 17 Nm³/h |
| heating oxygen pressure | 0,5 bar | 0,5 bar | 2,1 bar | 2,0 bar |
| heating gas consumption | 13 Nm³/h | 13 Nm³/h | 38 Nm³/h | 38 Nm³/h |
| heating gas pressure | 0,4 bar | 0,4 bar | 1,9 bar | 1,9 bar |
| cutting kerf | 5-6 mm | 6-8 mm | 7-9 mm | ca. 15 mm |
- suitable torches: GeGa, TCT, ALBA, Saldotecnica
- up to 300% increased longeivity
- about 35% lower gas consumption
| type | FraGa 15ES | FraGa 30E | FraGa 30ES | FraGa 50ES | FraGa 70ES |
| cutting thickness range | 50-150 mm | 150-350 mm | 150-350 mm | 300-500 mm | 450-700 mm |
| cutting oxygen consumption | 30 Nm³/h | 60 Nm³/h | 57 Nm³/h | 78 Nm³/h | 91 Nm³/h |
| cutting oxygen pressure | 10,0 bar | 10,0 bar | 10,0 bar | 8,0 bar | 7,0 bar |
| heating oxygen consumption | 9 Nm³/h | 16 Nm³/h | 9 Nm³/h | 18 Nm³/h | 16 Nm³/h |
| heating oxygen pressure | 0,9 bar | 2,0 bar | 0,9 bar | 2,1 bar | 2,0 bar |
| heating gas consumption | 26 Nm³/h | 24 Nm³/h | 26 Nm³/h | 35 Nm³/h | 35 Nm³/h |
| heating gas pressure | 1,1 bar | 1,5 bar | 1,1 bar | 1,9 bar | 1,9 bar |
| cutting kerf | 4,0 mm | 5,5 mm | 6,0 mm | 7,0 mm | 9,0 mm |
- suitable torch: Prestocut 1500
- pre-mixing
(The data refer to operation with natural gas, for values from operation with propane please contact us).
| type | DB 0300N-PM-06 | DB 0600N-PM-06 |
| cutting thickness range | bis 300 mm | bis 600 mm |
| cutting oxygen consumption | 50 Nm³/h | 100 Nm³/h |
| cutting oxygen pressure | 10 bar | 10 bar |
| heating oxygen consumption | 12,5 Nm³/h | 4-11 Nm³/h |
| heating oxygen pressure | 1,0 bar | 0,3-0,7 bar |
| heating gas consumption | 17 Nm³/h | 6-9 Nm³/h |
| heating gas pressure | 1,0 bar | 0,3-0,7 bar |
| cutting kerf | 6-7 mm | 8-10 mm |
framag PB - PM06
- suitable torch: Prestocut 600
(The data refer to operation with natural gas, for values from operation with propane please contact us).
| type | PB 0200N-PM-06 | PB 0300N-PM-06 | PB 0400N-PM-06 | PB 0600N-PM-06 |
| cutting thickness range | bis 200 mm | bis 300 mm | bis 400 mm | bis 600 mm |
| cutting oxygen consumption | 30 Nm³/h | 60 Nm³/h | 57 Nm³/h | 78 Nm³/h |
| cutting oxygen pressure | 10,0 bar | 10,0 bar | 10,0 bar | 8,0 bar |
| heating oxygen consumption | 9 Nm³/h | 16 Nm³/h | 9 Nm³/h | 18 Nm³/h |
| heating oxygen pressure | 0,9 bar | 2,0 bar | 0,9 bar | 2,1 bar |
| heating gas consumption | 26 Nm³/h | 24 Nm³/h | 26 Nm³/h | 35 Nm³/h |
| heating gas pressure | 1,1 bar | 1,5 bar | 1,1 bar | 1,9 bar |
| cutting kerf | 4,0 mm | 5,5 mm | 6,0 mm | 7,0 mm |
framag PB - PM12
- suitable torch: Prestocut 1200
(The data refer to operation with natural gas, for values from operation with propane please contact us).
| type | PB 0300N-PM12 | PB 0600N-PM12 | PB 0900N-PM-12 | PB 1200N-PM-12 |
| cutting thickness range | bis 300 mm | bis 600 mm | bis 900 mm | bis 1200 mm |
| cutting oxygen consumption | 35-60 Nm³/h | 60-120 Nm³/h | 140-200 Nm³/h | 200-300 Nm³/h |
| cutting oxygen pressure | 5-8 bar | 7-10 bar | 10-18 bar | 18-30 bar |
| heating oxygen consumption | 5-7 Nm³/h | 7-10 Nm³/h | 10-18 Nm³/h | 18-30 Nm³/h |
| heating oxygen pressure | 0,2-0,3 bar | 0,3-0,5 bar | 0,4-0,6 bar | 0,6-1,0 bar |
| heating gas consumption | 10-15 Nm³/h | 15-30 Nm³/h | 30-35 Nm³/h | 55-80 Nm³/h |
| heating gas pressure | 0,2-0,3 bar | 0,3-0,5 bar | 0,5-0,8 bar | 0,8-1,0 bar |
| cutting kerf | 5-10 mm | 10-15 mm | 15-20 mm | 18-35 mm |
framag PB - PM15
- suitable torch: Prestocut 1500
(The data refer to operation with natural gas, for values from operation with propane please contact us).
| type | PB 1500N-PM15 | PB 2000N-PM15 |
| cutting thickness range | bis 1500 mm | bis 2000 mm |
| cutting oxygen consumption | 375-440 Nm³/h | 440-500 Nm³/h |
| cutting oxygen pressure | 8 bar | 7-10 bar |
| heating oxygen consumption | 33 Nm³/h | 35-45 Nm³/h |
| heating oxygen pressure | 0,6-1,0 bar | 0,6-1,0 bar |
| heating gas consumption | 100 Nm³/h | 100-140 Nm³/h |
| heating gas pressure | 1,2 bar | 1,2-1,8 bar |
| cutting kerf | 25-50 mm | 30-70 mm |
framag PB - PM20
- suitable torch: Prestocut 2000 - GIGANT
(The data refer to operation with natural gas, for values from operation with propane please contact us).
| type | PB 1200N-PM20 | PB 2000N-PM20 | PB 2500N-PM-20 |
| cutting thickness range | bis 1200 mm | bis 2000 mm | bis 2500 mm |
| cutting oxygen consumption | 220-320 Nm³/h | 375-500 Nm³/h | 450-600 Nm³/h |
| cutting oxygen pressure | 7-10 bar | 5-7 bar | 5-7 bar |
| heating oxygen consumption | 23-30 Nm³/h | 33 Nm³/h | 33 Nm³/h |
| heating oxygen pressure | 0,2-0,3 bar | 0,3 bar | 0,3 bar |
| heating gas consumption | 70-90 Nm³/h | 100 Nm³/h | 100 Nm³/h |
| heating gas pressure | 0,8-1,1 bar | 1,2 bar | 1,2 bar |
| cutting kerf | 15-40 mm | 25-70 mm | 65-100 mm |
- Cutting material thickness up to 700mm
- Connections according to DIN EN 560
- Fuel gases: natural gas, propane, acetylene
- lengths: 500, 1000, 1300mm
- Special lengths on request
- Water cooling up to the nozzle
- Easy repair possibility
- Integrated pilot flame (or separate for internal mixing nozzles)
Available torch models of the Prestocut 600 series
- Prestocut C 635
- Prestocut C 655
- Prestocut C 651
- Prestocut C 6513
- Prestocut C 6513G
- Prestocut C 6515G
- Prestocut C 6525G
- Prestocut C 6535G
- Prestocut C 6545G
- Cutting material thickness up to 1200mm
- Connections according to DIN EN 560
- Fuel gases: natural gas, propane
- lengths: 500, 1000mm
- Special lengths on request
- Water cooling up to the nozzle
- Easy repair possibility
- Integrated pilot flame (or separate for internal mixing nozzles)
- Angle head adapter optionally available
Available torch models of the Prestocut 1200 series
- Prestocut 1255
- Prestocut 1251
- Cutting material thickness up to 1500mm
- Connections according to DIN EN 560
- Fuel gases: natural gas, propane
- lengths: 1000mm
- Special lengths on request
- Water cooling up to the nozzle
- Easy repair possibility
- Integrated pilot flame (or separate for internal mixing nozzles)
- Angle head adapter optionally available
Available torch models of the Prestocut 1500 series
- Prestocut 1571
- Cutting material thickness up to 2500mm
- Connections according to DIN EN 560
- fuel gases: natural gas, propane
- length: 1000mm
- Special lengths on request
- Water cooling directly to the nozzle seat
- Easy repair possibility
- Integrated pilot flame
- Mounting possibility for additional gas and powder supply in the torch head
Available burner models of the GIGANT 2000 series
- GIGANT 2000
Of course, in addition to torches & nozzles, we also offer all other spare & wear parts for all flame cutting systems. Here is a small excerpt from our assortment - Please contact us if required!
- Angle head adapter
- Pressure screws
- Check cartridges
- Pressure regulator
- Hoses
- Repair kits for pressure regulators
- Pilot burner
- manual cutting torch
- Hand cutting torch
- Gas control stations
- Protective devices
- etc.
✔ Easily exchangeable teeth
✔ Low-noise operation & long service life
✔ Long service life
✔ Significant cost reduction
✔ Suitable for all sawing systems
✔ Rapid availability
Together with a renowned manufacturer of cutting tools, a saw blade with exchangeable cutting teeth was created in a development partnership.
The carbide inserts for higher cutting speeds with higher tooth feed enable very small cutting widths. The costs for the user are significantly reduced with framag x:blade.
Do you need spare parts for one of your sawing systems? Regardless of the manufacturer and model, we are happy to offer you our expertise in equipment servicing as well as a wide range of spare parts.
An excerpt from our wide range:
- Damping plates
- Chip brushes
- Drive belts
- Belt pulleys
- Clamping sets
- Support plates
- Saw blade and accessories
- Fixing bolts for saw blades
- Gear boxes
- Consumables like cutting oil, grease...
- etc.
For a carefree maintenance of your plant we recommend to conclude a service contract. We take care of your machine - you profit!
Our maintenance contracts are specifically tailored to your needs. Here is an excerpt of the possible services:
- Annual inspection incl. inspection report
- Special conditions for travel time
- Special conditions for spare and wear parts
- Preferential support in case of malfunctions
- framag Service APP
- Stock keeping of spare parts
- Flat rate for spare & wear parts
- On-call service for maintenance
